4-Pin SurRon Charging Port – Female Panel Mount Battery Connector

The 4-Pin SurRon charging port is a female panel mount charging socket built for SurRon electric dirt bike batteries. It carries four contacts and installs directly into the battery lid or housing. As a result, the pack keeps its OEM-style charging connection.

This connector is the socket side, so it lives on the battery. The plug (male) half stays on the charger cable. Because of that, your charger connects exactly the way it does on a factory pack. No adapters and no rewired charger leads are needed.

This is a replacement part for repair or connector upgrade work. It is not a charger and it is not a battery. Wires are attached according to your own battery wiring diagram, with polarity confirmed before use. Battery builders, repair shops and hands-on SurRon owners all use this socket.

Key Benefits

• OEM-style connection – keeps the factory charging interface, so the standard charger plug still fits.
• Four-contact layout – matches the SurRon charging connector type with current and signal contacts.
• Stable contact – reliable charging current transfer across all four pins.
• Panel mount design – the socket recesses into the battery lid, so no wires hang loose.
• Replacement part – suits swapping out a damaged SurRon charging port.
• Upgrade option – used to modernise an old or worn charging socket.
• Correct female orientation – the right side for the battery, matched to the charger plug.
• Free wiring choice – use cable of the cross-section your battery configuration calls for.

Who Is This For?

This 4-pin charging connector is made for SurRon batteries. It mounts on the battery lid or housing of a SurRon electric dirt bike, including SurRon Light Bee packs. Compatibility with a specific charger depends on the plug type and the contact arrangement.

Battery assemblers and repair workshops use this socket as a standard stock item. Experienced owners also pick it when replacing a damaged charging port themselves. In addition, the connector suits a self-built SurRon-type battery pack that needs an OEM-style charging point.

Typical use cases include three jobs. First, replacing a cracked or burnt socket. Second, assembling a new battery housing from scratch. Third, refreshing the connector after hard off-road use. Before ordering, compare the contact arrangement on your own charger plug.

Package Contents

• 1 pc – 4-Pin female charging connector

Gasket and nut inclusion depends on the batch. If you need a specific set of parts, get in touch before ordering.

Technical Specifications

Installation Notes

• Disconnect the battery and discharge the system before starting work.
• Check polarity and contact layout against the OEM diagram.
• Use cable of a suitable cross-section for your pack.
• Crimp the terminals properly or solder them cleanly.
• Fit a gasket or sealant for water resistance if none is supplied.
• Test voltage and polarity after installation, before you plug in the charger.

Why Choose This 4-Pin SurRon Charging Port?

The socket retains the OEM-style connection, so the charger plug seats normally. Therefore you avoid rewiring the charger lead or relying on in-between adapters. That saves time on any repair job.

Panel mounting locks the socket firmly into the housing. As a result, the connector handles frequent plugging and unplugging of the charger. A recessed, solidly fixed socket also snags less in off-road conditions.

Since this is a standalone spare part, you can repair the battery charging point on its own. In other words, there is no need to replace the whole battery pack because of one broken socket.

FAQ

Does this connector work as the battery-side socket?

• Yes, it is a female connector for panel mounting on the battery.
• The male plug stays on the charger side.

Is this 4-Pin connector compatible with all SurRon chargers?

• Compatibility depends on the plug type and contact arrangement.
• If your charger uses the same 4-pin standard, it matches.
• Compare your charger plug before ordering.

Where does the connector mount on a SurRon battery?

• On the battery lid or the battery housing.
• It is a panel mount design, so the socket sits recessed.

Does the SurRon charging port come with a charger or battery?

• No. This listing covers the connector only.
• One female connector is supplied.

How are the wires connected?

• According to your own battery wiring diagram.
• Polarity must be observed at all times.
• Crimped terminals or clean soldering are both suitable.

Is a gasket and nut included?

• That depends on the production batch.
• Contact us first if you need a specific configuration.

Is the connector waterproof?

• Moisture resistance depends on the batch and on how the housing is sealed.
• Adding a gasket or sealant during installation helps.

Can I use it on a custom-built battery pack?

• Yes, it suits a self-built SurRon-type pack.
• It gives that pack an OEM-style charging point.

Whether you are rebuilding a burnt socket, assembling a fresh housing or refreshing a worn charging point, this four-contact female connector restores the factory charging interface on your SurRon battery. Check your charger plug layout, wire it to your pack diagram, and verify polarity before the first charge.