This SurRon / Talaria Sting battery box is an empty stainless steel enclosure built for the Sur-Ron Light Bee (L1E / X) and the Talaria Sting electric dirt bike. It measures roughly 35.5 cm in height. Both the shell and the lid are made from stainless steel. Inside, the box is completely bare.
The kit ships with a lid, a carry strap handle, 8 mounting bolts and an output cable grommet. No cells, no BMS and no charger are included. This is an aftermarket part, so it fits by dimensions rather than by a manufacturer catalogue number. Always measure your existing pack before ordering.
Riders choose this enclosure for two reasons. Some need a rugged shell for a home-built battery pack. Others need a replacement housing after a crash or corrosion damage. In both cases, the metal construction shields the pack from impacts, mud and weather on rough trails. Meanwhile, the removable lid and strap make pulling the block in and out simple, and the single cable entry keeps the wiring tidy.
Key Benefits
- Stainless steel construction – the shell resists impacts and deformation during off-road riding.
- ~35.5 cm height – this is the defining measurement for matching a Sur-Ron or Talaria Sting battery block.
- Removable lid – reach the battery block without stripping down the whole enclosure.
- Carry strap handle – pull the block out and carry it one-handed.
- Output cable grommet – seals the cable entry against mud and moisture.
- 8 bolts included – the bolted mounting points are ready to install straight away.
- Suits custom-built packs – provided the block stays within ~35.5 cm in height and the base dimensions.
- Metal instead of plastic – shell and lid are stainless steel rather than a moulded plastic panel.
Who Is This Battery Box For?
This enclosure is aimed at riders of the Sur-Ron Light Bee L1E, the Sur-Ron Light Bee X and the Talaria Sting. All three are electric dirt bikes with a removable 60 V battery block. Before you buy, check the dimensions of your own pack and the layout of its connectors.
Battery builders form the second group. They pick this housing when they need a sturdy shell that matches the original battery bay of a Light Bee or Sting. The ~35.5 cm height and the base dimensions decide whether a custom pack will drop in cleanly.
A third situation is replacement work. After a fall or after corrosion sets in, the old housing gets swapped out. The rider then moves the existing block into the new metal box and rebuilds a clean cable route through the single grommet entry.
What’s in the Box?
- Battery enclosure, approximately 35.5 cm tall
- Lid
- Carry strap handle for lifting and extraction
- 8 mounting bolts
- Output cable grommet for sealing
A display screen and the charge / discharge connectors are not included. Those are purchased separately.
Technical Specifications
| Product type | Battery box (empty enclosure, no cells) |
| Height | ~ 35.5 cm |
| Material | Metal – stainless steel (shell and lid) |
| Sealing | Grommet for the output cable |
| Mounting | Bolted mounting points, 8 bolts included |
| Carrying | Strap handle |
| Compatibility | Sur-Ron Light Bee (L1E / X), Talaria Sting, custom-built batteries |
| Not included | Display, charge / discharge connectors, cells, BMS |
| Part type | Aftermarket part |
Why Choose This Enclosure?
The shell and lid are stainless steel. As a result, the structure absorbs the knocks and vibration that no bike escapes off-road. Metal also cracks less readily around the bolt points than moulded plastic does.
Second, the box arrives ready to work with. The 8 bolts and the cable entry grommet are already in the kit, so there is no hunting for small parts. Furthermore, the strap handle makes daily extraction of the block far less awkward.
Third, the ~35.5 cm height matches the battery bay dimensions of the Sur-Ron Light Bee and the Talaria Sting. Consequently, the housing also suits custom-built packs that stay within that measurement.
Frequently Asked Questions
Will my battery fit inside?
- The internal height is around 35.5 cm, so your block must not exceed it.
- Measure the height, width and depth of your pack before mounting.
- Check the connector layout too, since terminals must not press against the lid.
Does it fit the Sur-Ron Light Bee L1E and X?
- Yes, the enclosure is built around the Light Bee L1E and Light Bee X battery bay.
- Fitment is by dimensions, not by a factory catalogue number.
- Compare your bay measurements against the ~35.5 cm height first.
Is it compatible with the Talaria Sting?
- Yes, the Talaria Sting is one of the listed compatible bikes.
- The Sting uses a removable 60 V battery block, like the Light Bee.
- Verify your own pack dimensions and connector positions before ordering.
Are cells or a BMS included?
- No. The enclosure ships completely empty.
- There are no cells, no BMS and no charger inside.
- You supply the pack, or build one to suit the housing.
What hardware comes with it?
- A lid, a carry strap handle and 8 mounting bolts.
- An output cable grommet for sealing the wiring entry.
- The bolted mounting points are ready for immediate installation.
Can I use it for a custom battery build?
- Yes, this is a common use for the enclosure.
- Your finished block must respect the ~35.5 cm height and base dimensions.
- Route the main cable through the grommet to keep the entry sealed.
Is this an original Sur-Ron part?
- No, it is an aftermarket enclosure.
- It matches by physical dimensions rather than by catalogue number.
- Confirm the measurements against your bike before fitting.
Does it keep out mud and water?
- The grommet seals the output cable entry against mud and moisture.
- The stainless steel shell and lid shield the pack from impacts and debris.
- A single cable entry keeps the wiring route tidy.
In short, this is a bare stainless steel housing for Sur-Ron Light Bee and Talaria Sting battery blocks, supplied with a lid, strap handle, 8 bolts and a cable grommet. Measure your pack height against the ~35.5 cm figure, plan the connector layout, and remember that the display and charge connectors are sold separately.
There are no reviews yet.