Motor to Controller Cable 1000W 60cm – 9-Pin IP65 Connector

This motor to controller cable is a 60 cm connecting lead built for electric drive systems rated between 250 W and 1000 W. It links the motor to the controller on e-bikes, electric scooters and other light electric vehicles. A single 9-pin connector carries both the motor phase wires and the sensor and signal lines.

The cable fits hub motors (motor built into the wheel) and BLDC motors. Because everything runs through one sealed plug, you no longer need several separate leads between the two components. That keeps wiring tidy inside a bicycle frame or a scooter deck. The IP65 rating protects the contacts from dust and water spray.

Use it to replace a damaged connector, repair a broken lead, or refresh the wiring on an existing build. Before ordering, check the connector type and pin layout on your own controller and motor. The pinout must match your system for the cable to work correctly.

Key Benefits

• Wide power range – runs steadily across 250 W to 1000 W drive systems.
• Nine pins in one plug – carries motor phases plus sensor and signal lines according to your wiring diagram.
• IP65 protection – resists dust and water spray, so it stays reliable in daily use and in rain.
• Compact 60 cm length – suits replacements and short-run connections without surplus cable to coil up.
• Tough outer jacket – handles bending and vibration on rough road surfaces.
• Sealed connector – keeps the contacts shielded from moisture and road grime.
• Plug-and-play fitting – no extra soldering needed when the connector type and pin layout match.
• Dual application – works on electric bicycles and electric scooters alike.

Who Is This Cable For?

This lead suits electric bicycles, electric scooters and other light electric vehicles with motor output between 250 W and 1000 W. It joins the motor to the controller and passes both power and signals through the same run. Owners of hub motor builds and BLDC motor builds will find it a direct fit for rewiring work.

Repair technicians use it to replace a connector damaged by a fall or worn down over time. Home builders reach for it when assembling an e-bike from separate components. In both cases, the short run keeps the loom neat rather than leaving slack to manage.

The 60 cm length is measured for connections routed inside a frame tube or along a scooter platform. Nevertheless, confirm first that the connector type and pin arrangement match your controller and motor. A mismatched pinout will not deliver correct operation.

Technical Specifications

Why Choose This 60 cm Motor Cable?

The main difference is one 9-pin plug instead of several separate connectors. As a result, you do not have to wire the phase lines and the Hall sensor lines apart from each other. That cuts the chance of a wiring mistake and shortens the job considerably.

The IP65 rating means the joint is sealed against dust and copes with water spray from the road. This matters on wet commutes and rainy days. However, the cable is not designed for submersion in water.

The 60 cm length was chosen to bridge the usual gap between controller and motor. At the same time, it avoids a coil of leftover cable inside the frame. Moreover, the sturdy insulating jacket withstands repeated flexing near the handlebar or frame line.

Frequently Asked Questions

Will this cable work with a system rated above 1000 W?

• This model covers systems up to 1000 W.
• The rated range is 250 W to 1000 W.
• Higher-output systems need a cable matched to that power level.

Is the connector plug-and-play?

• Yes, provided the connector type and pin layout match your system.
• Check the controller and motor connectors before you buy.
• If the pin arrangement differs, the cable will not function correctly.

Does it fit hub motors and BLDC motors?

• Yes, it is intended for hub motor and BLDC motor installations.
• It suits both replacement work and wiring upgrades.
• The pinout still has to correspond to your existing loom.

What does the 9-pin connector actually carry?

• The motor phase wires.
• The sensor and signal lines.
• Both travel through one sealed plug instead of multiple leads.

Can I use it on an electric scooter as well as an e-bike?

• Yes, it fits electric scooters, electric bicycles and light electric vehicles.
• The 60 cm run suits routing along a scooter deck.
• It also works for connections inside a bicycle frame.

Is the cable safe in the rain?

• The IP65 rating covers dust ingress and water spray.
• That makes it dependable on wet roads.
• It is not rated for immersion in water.

Is 60 cm long enough for my build?

• The length is sized for the typical controller-to-motor distance.
• It avoids excess cable that needs coiling.
• Measure your own routing path before ordering.

This 9-pin cable brings the motor phases and sensor lines together in a single sealed link between motor and controller. With its IP65 seal, tough jacket and 60 cm run, it serves both repairs and fresh builds on 250-1000 W drive systems. Confirm your connector type and pin layout, then fit it without soldering.