Magura MT7 PRO Hydraulic Disc Brake – 4-Piston, 2200 mm Hose

The Magura MT7 PRO is a hydraulic disc brake for a single wheel, front or rear. It fits mountain bikes, e-MTBs, S-Pedelec speed e-bikes and electric scooters. Moreover, it works as a braking upgrade on Sur-Ron and Talaria electric motorcycles with the matching adapters.

The set pairs a 4-piston caliper with a radial master cylinder and a one-finger HC lever. A 2200 mm brake hose comes fitted, which is longer than the usual 1600-1700 mm rear line. Therefore, long-frame electric platforms can be plumbed without swapping the hose.

Construction centres on a Carbotecture® SL body and an aluminium lever blade. Weight sits at roughly 255 g per brake, excluding rotor and adapter. As a result, the same brake suits a light trail bike and a heavier e-platform equally well.

Key Benefits

• 4-piston caliper – even pad pressure across the pad face and a large reserve of braking power.
• One-finger HC lever – sensitive modulation and less hand fatigue on long descents.
• Radial master cylinder – lower friction, quicker response and more precise control at the bite point.
• Carbotecture® SL body – a light yet rigid housing paired with an aluminium lever.
• 2200 mm brake hose – the long version, made for rear brakes on stretched e-platform frames.
• Rotating hose port at the caliper – simpler routing along the fork leg or frame.
• High thermal capacity – less brake fade when heat builds up on sustained descents.
• 8.P Performance pads – fitted from the box and matched to the four-piston caliper.
• Around 255 g per brake – a low figure for a four-piston system, measured without rotor or adapter.

Who Is This For

Enduro and downhill riders gain the most from this brake. Four pistons and 8.P Performance pads keep braking reserve available deep into long descents. In addition, the one-finger lever lets you meter force on technical sections without moving your grip.

On the electric side, the MT7 PRO is used on e-MTB builds, S-Pedelec speed e-bikes and electric scooters. It also serves as a braking upgrade for Sur-Ron and Talaria electric motorcycles, including Sur-Ron Light Bee builds. For those machines, pair it with the correct adapter and a 203 or 220 mm rotor.

Riders carrying more mass and more speed benefit as well. Heavier bikes load the brake harder, so consistent stopping matters. Mounting stays universal, since the adapter is chosen by frame or fork and rotor diameter.

What’s In The Box

• 1× brake lever assembly – master cylinder with one-finger HC lever
• 1× 4-piston brake caliper
• 1× 2200 mm brake hose
• 2× hose fittings – olive and insert

The rotor and the caliper mounting adapter are not included. Choose both according to your frame or fork and a 203 or 220 mm rotor diameter.

Technical Specifications

Why Choose The Magura MT7 PRO

The MT7 PRO sits at the top of Magura’s four-piston range. Magura has built braking systems in Germany since 1893. The PRO version keeps the same brake core as the standard MT7, simply without the extra lever accessories.

Braking starts smoothly, without an abrupt bite. Consequently, stopping distances shorten while tyre grip stays easier to read. On technical ground you can dose power with a single finger and keep the other fingers on the bar.

The long hose is the second differentiator. At 2200 mm it clears the extended rear triangles found on e-platform frames. Because of that, many builds go together without cutting in a replacement line.

Frequently Asked Questions

Does the Magura MT7 PRO fit a Sur-Ron or Talaria?

• Yes, it is used as a braking upgrade on both machines.
• You need the correct caliper adapter for the frame or fork.
• Rotor sizes of 203 or 220 mm are recommended.

Is this brake suitable for an e-MTB or S-Pedelec?

• Yes, it covers mountain bikes, e-MTB and S-Pedelec builds.
• Electric scooters are supported as well.
• The four-piston caliper handles the extra mass of electric platforms.

Is this one brake or a pair?

• The set covers one wheel only, front or rear.
• Order two sets for a complete front and rear installation.

Why is the hose 2200 mm long?

• Standard mountain bike rear hoses run about 1600-1700 mm.
• The longer line reaches the rear caliper on stretched frames.
• No hose replacement is needed on most long-frame builds.

Are a rotor and adapter included?

• No, both are selected separately.
• Pick the adapter by frame or fork mount and rotor diameter.
• Rotor options are 203 or 220 mm.

Which brake fluid does it use?

• Mineral oil, specifically Magura Royal Blood.
• The system arrives filled and ready to install.

How does the PRO differ from the standard MT7?

• The brake core is identical between the two versions.
• The PRO simply omits the additional lever accessories.

What pads does it come with?

• 8.P Performance pads are fitted as standard.
• All four pistons press them evenly against the rotor.

Choose the Magura MT7 PRO when you need four-piston stopping power on a mountain bike, e-MTB, S-Pedelec, electric scooter, Sur-Ron or Talaria. Add a 203 or 220 mm rotor plus the adapter that matches your frame or fork, and the 2200 mm hose handles the rest.