ODI Alloy End Plugs – Anodised Bar End Plugs for Sur-Ron, Talaria, E-Ride PRO

ODI Alloy End Plugs are anodised aluminium bar end plugs built for Sur-Ron, Talaria and E-Ride PRO electric dirt bikes. They also fit MTB and BMX handlebars. The plugs suit any Ø22.2 mm (7/8″) bar, which is the standard diameter across e-moto and bicycle cockpits. Each set is sold in pairs, so both bar ends are covered from the first install.

On almost every standard handlebar, the tube ends sit open. During a crash, that open tube edge becomes a genuine hazard. These plugs seal both ends and shield the grips at the same time. Inside the bar, three expanding cores grip the tube wall and hold the plug in place.

The plugs are machined from 6061 aluminium alloy and measure 32 mm across the outer face. Because the finish is anodised rather than painted, the colour stays true through repeated riding seasons. Five colours are available: black, silver (grey), blue, red and orange.

Key Benefits

• 6061 anodised aluminium – light, durable and resistant to both corrosion and scratching.
• Triple-core locking design – three cores expand inside the handlebar and lock firmly against the tube wall.
• Stays put – the plugs neither rotate nor drop out, even after hard riding sessions.
• Grip protection – covers the bar ends during a fall or when brushing walls and trees.
• 22.2 mm bar compatibility – suits standard MTB, BMX and e-moto handlebars.
• Five anodised colours – black, silver (grey), blue, red and orange.
• Sold in pairs – 2 pieces per set, ready for both sides of the bar.
• Fast fitting – the plugs push in easily and come out again without extra parts.

Who Are These Bar End Plugs For?

These end plugs are made for Sur-Ron, Talaria and E-Ride PRO electric dirt bikes. Beyond those models, they also fit most other electric bicycles along with MTB and BMX cockpits. The one requirement is a 22.2 mm (7/8″) handlebar diameter.

Riders who spend time on forest trails, motocross tracks or tight urban lines benefit most. In those conditions, the bar ends regularly contact trees, walls and other obstacles. Sealed ends therefore reduce grip wear over the life of the bike.

The plugs also suit riders who colour-match their build. Orange or blue plugs, for instance, tie the cockpit together with the grips or frame accents. Because five colours are offered, most factory and custom colourways can be matched.

What’s in the Box

• 2 × ODI Alloy End Plugs bar end plugs (a pair, for the left and right side)

Technical Specifications

Why Choose ODI Alloy End Plugs

ODI (O’Neal Design Inc.) is an American manufacturer founded in 1981 in Ontario, California. The company specialises in grips and handlebar components. It also developed the lock-on grip system used throughout motocross. Handlebar hardware is therefore this brand’s core competence, not a side line.

Instead of a plastic cap, this design uses 6061 aluminium alloy. As a result, the plug does not shatter on impact and survives repeated crashes. The anodised layer holds its colour longer than paint, since anodising is an electrochemical surface treatment rather than a coating applied on top.

Triple-core locking also outperforms a single-bolt solution. Three points press against the inner wall of the handlebar tube, so the load spreads evenly across the contact area. Consequently the plug sits stable during riding, yet it still pulls out easily when you need to service the bar.

Frequently Asked Questions

Will ODI Alloy End Plugs fit Sur-Ron and Talaria bikes?

• Yes, these plugs fit Sur-Ron, Talaria and E-Ride PRO electric dirt bikes.
• These machines use standard 22.2 mm (7/8″) handlebars.

Do they work on an E-Ride PRO or a regular MTB?

• Yes, E-Ride PRO bikes are directly supported.
• They also fit MTB and BMX bars measuring 22.2 mm.

How many plugs come in a set?

• Each set contains 2 pieces, sold as a pair.
• That covers both the left and right side of the handlebar.

What holds the plug inside the handlebar?

• A triple-core design expands three cores against the inner tube wall.
• Because the load spreads over three points, the plug does not slip or rattle.

Which colours are available?

• Black, silver (grey), blue, red and orange.
• All five finishes are anodised rather than painted.

What is the outer diameter?

• The outer face measures 32 mm.
• The plug body is sized for a Ø22.2 mm handlebar bore.

Can the plugs be removed later?

• Yes, fitting and removal need no additional parts.
• The plugs push in by hand and come back out when required.

Do they actually protect the grips?

• They cap the open bar ends during falls and scrapes against walls or trees.
• This reduces grip wear on trail, track and tight city riding.

ODI Alloy End Plugs bring together 6061 anodised aluminium, a triple-core lock and a 32 mm outer face in a pair that installs in seconds. Whether the bike is a Sur-Ron, a Talaria, an E-Ride PRO or a 22.2 mm MTB build, the open bar ends get sealed and the grips gain a layer of protection. Pick the colour that matches your cockpit and finish the build properly.