The Torp TC500 2.X FOC motor controller kit (motor controller kit) is designed specifically for the Talaria MX5 electric off-road bike (e-moto). This aftermarket controller runs on 60–80 V nominal battery systems (22S) and supports up to 25 kW output.
The TC500 2.X connects by Bluetooth (Bluetooth communication) to a mobile app (mobile app) for setup and diagnostics. The kit includes a wiring harness (wiring harness) and a thumb throttle (thumb throttle) for Talaria MX5 installations.
It supports both Hall sensor control (Hall / HALL Encoder) and sensorless control (sensorless control), so you can match the control mode to your Talaria MX5 configuration. However, it currently cannot communicate via CAN bus (CAN) with the SCUD-made stock Talaria battery.
Key benefits of the Torp TC500 2.X FOC Controller for Talaria MX5
- FOC control (field-oriented control) – the controller uses FOC and is rated up to 99% efficiency.
- Up to 25 kW power – TC500 2.X is intended for higher Talaria MX5 drivetrain load than stock electronics.
- 60–80 V nominal (22S) support – compatible with 22S packs and works up to 92.4 V when fully charged.
- 700 A max battery current – enables high-current configuration when a high-capacity 22S battery demands it.
- 500 A max phase current – targets higher torque requests through phase current control.
- Bluetooth + iOS/Android app – wireless access to settings and diagnostics through the mobile app (iOS & Android).
- Hall or sensorless operation – supports HALL Encoder (Hall sensors) and sensorless control for Talaria MX5 builds.
- Built-in protections – includes overcurrent, overvoltage, undervoltage, and overtemperature protection logic.
Who is this for?
This Torp TC500 2.X kit is for the Talaria MX5 electric enduro / electric off-road motorcycle (e-moto). It targets riders upgrading Talaria MX5 drive electronics to an aftermarket FOC controller with app-based configuration.
The controller is intended for Talaria MX5 setups using 60–80 V nominal (22S) battery configurations. It operates at up to 92.4 V fully charged, which aligns with typical 22S pack voltage behavior.
It suits Talaria MX5 owners who want selectable control modes, because it supports Hall-sensored control (HALL Encoder) and sensorless control. It also suits Talaria MX5 riders who want different regenerative braking modes (regen braking) and throttle modes configured through the app.
Package contents
- 1x Torp TC500 2.X controller (TC500 Controller)
- 1x wiring harness (wire harness / wiring harness)
- 1x thumb throttle (thumb throttle)
- 1x fuse with a plastic protection (fuse with a plastic protection)
- 1x connector cover (connector cover)
- 1x plastic shield (plastic shield)
- Screws and tools required for installation
- 2x installation brackets (installation brackets)
- 4x stickers (stickers)
- 1x silicone grease pack (silicone grease)
- Short instructions (short instructions)
Technical specs
| Product type | Aftermarket motor controller kit (motor controller kit) |
| Intended vehicle | Talaria MX5 electric off-road motorcycle (e-moto) |
| Control type | FOC (field-oriented control) |
| Nominal voltage range | 60–80 V nominal (22S) |
| Max voltage (fully charged) | 92.4 V (22S full charge) |
| Maximum power | Up to 25 kW |
| Maximum battery current | 700 A |
| Maximum phase current | 500 A |
| Sensor support | Hall sensor control (HALL Encoder) and sensorless control |
| Connectivity | Bluetooth communication (Bluetooth) |
| App support | Mobile App (iOS & Android) |
| Calibration | Pre-calibrated; calibration performed via mobile app |
| Display support | Stock SurRon display |
| BMS / battery communication note | No CAN bus communication with SCUD stock Talaria battery at this time; other functions operate normally |
| Protections | Overcurrent, overvoltage, undervoltage, overtemperature |
Why choose this Torp TC500 2.X kit?
This TC500 2.X package is sold as a complete Talaria MX5-oriented kit because it includes the wiring harness (wiring harness) and thumb throttle (thumb throttle). The included fuse with plastic protection, connector cover, and plastic shield support a cleaner Talaria MX5 controller installation.
Setup is app-driven through Bluetooth (Bluetooth communication) using the Mobile App on iOS or Android. The controller is pre-calibrated, and the calibration workflow is handled through the app for clearer first start behavior.
Control flexibility is built in, because TC500 2.X supports both HALL Encoder operation and sensorless control. The key limitation is CAN bus communication with the SCUD stock Talaria battery, which is not supported at this time.
FAQ
Is this Torp TC500 2.X controller kit compatible with the Talaria MX5?
- Yes, this aftermarket motor controller kit is designed for the Talaria MX5 e-moto.
- The kit includes a wiring harness and thumb throttle intended for Talaria MX5 installation.
What battery voltage does the TC500 2.X support on a Talaria MX5?
- It supports 60–80 V nominal battery systems (22S).
- It operates up to 92.4 V at full charge for 22S configurations.
What are the power and current limits of the Torp TC500 2.X?
- Maximum power is rated up to 25 kW.
- Maximum battery current is 700 A.
- Maximum phase current is 500 A.
Does the TC500 2.X work with Hall sensors and sensorless mode?
- Yes, it supports Hall sensor control (Hall / HALL Encoder).
- It also supports sensorless control, which you can choose based on the Talaria MX5 setup.
How do I configure the controller and run diagnostics?
- The controller uses Bluetooth communication for wireless access.
- Configuration and diagnostics are done through the mobile app (iOS & Android).
- Calibration is performed via the app, and the unit is supplied pre-calibrated.
Can the Torp TC500 2.X communicate with the stock SCUD Talaria battery over CAN?
- No, CAN bus communication with the SCUD-made stock Talaria battery is not supported at this time.
- Other controller functions operate normally even with this limitation.
What display support is listed for the TC500 2.X kit?
- The specification lists support for the stock SurRon display.
The Torp TC500 2.X for Talaria MX5 is an app-configurable FOC controller kit that combines 22S voltage support, up to 25 kW output, and Hall or sensorless operation in one package.
Search terms: Torp TC500 2.X motor controller kit (aftermarket controller) for Talaria MX5, FOC controller (field-oriented control), Bluetooth controller iOS Android, 22S 60V 80V 92.4V e-moto controller, Hall encoder (HALL) sensorless controller, 25kW Talaria MX5 controller, 700A battery current, 500A phase current, regen braking modes, thumb throttle, wiring harness.
